Dentrix Imaging supports acquiring intraoral images from the DEXIS DEXcam 3 or 4 camera on computers running the Windows operating system.
Note: Before installing the camera, you must install the acquisition agent application on each computer that you use to acquire images. Please refer to Setting up the acquisition agent for instructions on downloading and installing the acquisition agent.
You must install the drivers for the DEXIS DEXcam 3 or 4 camera on each computer that you use to acquire images.
Note: If a DEXIS DEXcam 3 or 4 camera was installed and operating previously with this computer, and you connect the camera to a USB port, Windows will not search for drivers because they are already installed. In this case, you can ignore these installation instructions and skip directly to the Testing section.
To install the drivers
1. Connect the DEXcam 3 or 4 camera to a USB port on the computer.
Notes:
· Windows detects the device, starts searching for the drivers, and then installs them.
· The drivers for DEXcam3 and DEXcam4 camera are available through the Windows Update service, so the computer must have internet access.
2. To prevent technical issues in the future, connect the camera to every USB port on the computer. This is to ensure that the device will be recognized no matter which port it is connected to.
The DEXcam3 and DEXcam4 cameras are now functional and ready to acquire images.
To acquire a test image
1. In the Imaging Procedures list, click 2D Oral/Facial Photo Images.
2. In the Acquisition method for this imaging exam menu, click DEXcam 3/DEXcam 4, and then click Proceed with Acquisition.
Notes:
· If a message about the browser not being able to access the camera appears, refer to the steps in the Troubleshooting section of this guide.
· To access basic camera settings, click the cog icon (in the upper-right corner of the snapshot panel).
3. If more than one camera is connected to the computer, or if the computer has a built-in webcam, Google Chrome may not select the intraoral camera by default. If this happens, to select the correct camera, do the following:
a. Click the camera icon (in the upper-right corner of the snapshot panel).
b. Select the option that corresponds to the correct camera, and then click Change Source.
Note: You may need to be restart the browser for the changes to take effect.
After you have configured the camera and started an acquisition, a live video stream from your camera appears.
4. With the camera properly positioned, use the button on your camera to pause or freeze the live video stream (or click Pause Streaming).
5. Use the button on your camera to capture the current video frame (or click Take a snapshot).
The resulting image is added to the snapshot panel, and the video stream automatically becomes live again.
6. Repeat steps 4-5 as needed to acquire additional snapshots.
7. On the snapshot panel, clear the check box of the snapshots that you do not want to save.
8. Click Assign Images.
9. Do any of the following:
· To save one or more snapshots as intraoral images and assign tooth numbers, select the snapshots that pertain to the same teeth (deselect snapshots that do not pertain to the same teeth), and then drag them to the Select Teeth, UR/UL/LR/LL, Upper Jaw, or Lower Jaw box.
If you drag snapshots to the Select Teeth box, select the applicable teeth, and then click Assign Teeth.
· To save one or more snapshots as extraoral images, select the snapshots that are extraoral images (clear snapshots that are not extraoral images), and then drag them to the Extraoral Photos box.
· To save the snapshots on the snapshot panel as intraoral images, but not assign tooth numbers, leave those snapshots on the snapshot panel.
Assigned intraoral images appear on the left side of the preview area; extraoral on the right.
Note: If you have a mix of intraoral and extraoral images, they map to one procedure (D0350), which will appear in the progress notes with two icons. Also, you can delete or reassign the intraoral or extraoral exam as needed in the future.
10. Click Begin Uploading.
Confirm that the camera device driver is loaded and recognized by Windows.
To confirm that the camera device driver is loaded
1. Connect the camera to a USB port.
2. Open Device Manager.
3. Expand the Cameras category, and make sure that the camera is listed.
4. Verify that the camera is working properly.
5. If your camera is not being detected by Windows, or if it appears with an error message, try unplugging the camera and plugging it into another USB port on the computer. If the problem persists, contact the camera manufacturer for additional assistance.
If the browser cannot access the camera, an error message appears.
To unblock the camera
1. In Chrome, click the View site information button on the left side of the URL box.
2. Select Site settings.
3. Change the Camera setting from Ask to Allow.
4. In the error message in Dentrix Imaging, click the Click here to retry after unblocking the camera link.